Видео

They have been solid. Had a minor leak in the smaller hose that goes to the engine bay, but I think it was my fault because all I did was tighten the clamp a little more and it went away. Water temp really did go down a couple degrees so it was worth it in my opinion.

Just a heads up that these gaskets are known to fail quickly and are a temporary fix. I'm getting ready to pull that whole assembly out following this video ruclips.net/video/AmK_AdtVuZA/видео.html Best of luck with your current and future repairs!

A reply from PPE support said to use Silicon grease (and that they get this complaint a lot, hah). Some other forums have also said this is more for a Mishimoto radiator setup. Either way, mine are holding up well, no leaks or coolant loss. I forgot to mention in the vid to be sure to put SOME sort of grease on them otherwise the O-ring is likely to tear or warp. If only I had seen a vid or post like this before, it would've taken me minutes instead of hours!

Also, thanks and best of luck on your build(s).

There's a t-bolt that I just unscrewed to get the metal fitting off. I just really tightened it back up once I jacked this mf'er fitting on there and it's still solid, hah. No leaks or drips.

@@EricEscamillaesca2791 man, mine are still leaking after all that blasted trouble. I’m hot about it all because I got to get back under there and undo everything. Pull all that crap apart and throw some high temp silicone on all the fittings. I’ve probably over tightened my clamps and jacked them up. It’s going to be a another process. Came back from a 4 hour drive and the top radiator hose was pouring out and hadn’t before. Ain’t nothing like losing $100 worth of coolant. Buy a solution for a fix for $300 and got to keep buying coolant. Imma get a “good” pressure tester this next time. After that they will be cut out…

@@jamesb3654 Real sorry to hear that. I've heard of some of these leaking, but I really bought into the "brand". Maybe my negative experience is right around the corner, but I know what you mean about blowing money on all that coolant, took me about 9 gallons before I got this down. Saved what I could - was literally there with cups, whatever I could get while the thing was leaking money.

@@EricEscamillaesca2791 exactly… I’m just dreading this… read up on a lot of the forums saying this was the ones to buy and maybe i just got a lemon set. Hopefully this go round is the last one till they rot. Hope you never have a problem with yours!

YES it did...BUT to test, stick a screwdriver where the the starter is and see if still no start. Afterwards, I had almost exact same issue with new starter, but it was the ignition cylinder or actuator... now I just put in a button to start it up.

It was the starter...I replaced the fuel pump and after the problem was still there I just had it diagnosed.

ganesh r Hi, I'm not sure about running ldap on windows, but as long as the connection string is right, it should work.

Sorry, I've tried that a couple times with no success and have had to drop it to move on to other projects for work. I mainly just use the queries because we have another system that does CRUD on our LDAPS. In my application I just need to know who belongs to what.

GD100 good evening and thank you, my family is extending by one (wife is pregnant) so I have been pretty pre-occupied, hah. I would like to make one on how I integrated this into a web application; however, I just haven't gotten around to it. are you encountering an issue? And yes, I really do need to commit this to github. I will get back to you on that.

Hi Irvan, hope all is well. That seems to be just related to an invalid username/password. Also, is it LDAPS?

Eric Escamilla yup it is LDAP, this AuthenticationException: [LDAP: error code 49 - Invalid Credentials bother me, how can i go well on terminal but cant on this TT, have any idea ? or can you list up, what should i do the beginning installing ldap and what i have to setting? this is my reference techpubs.spinlocksolutions.com/dklar/ldap.html

Hi, may you give me the output/stack trace? Or what the error is related to? Thanks!

Eric Escamilla I solved it because of ldap base. I don't know well about the problems. just Eclipse show me message. The message is nested exception is javax.naming.SizeLimitExceededException, [LDAP:error code 4 - Sizelimit Exception]. It may be my fault and low level about spring and LDAP. i could solve this problem as I add code "ou=??" in String base.

Park Songwon Hmm, it seems you were being returned over 1000 rows (which is an LDAP limit), and then adding ou possibly filtered down the results. I'm not sure of the size of your LDAP db though.

Sure, you may want to consider updating though if you have the option to. JSP and even JSTL integration is harder since that is mixing "old spring" with "new spring". You just need the spring ldap jar though from the dependency mentioned in this pom.xml. As far as your project setup, is that setup using spring?

I dont really know about spring but i know this is what i'm need, where can i download the jar ? I have searching for it on offcial site ,but it just give me helloworld

You need a dependency management tool such as maven to manage your pom.xml, in that pom.xml, that is where you declare all the mentioned dependencies/jars. I included the my pom.xml in the link below the video. I would recommend the newest version of spring web applications, spring boot.

irvan kosini spring.io/guides/gs/spring-boot/

Eric Escamilla , thank you , i want to implement this on debian and i think this woud work on it :D can i have a discussion with you if i'm stuck at some problem ?

praveen akula Hi Praveen, sorry it's been a while. May you send me the stack trace? Or what line is it error-ing on? Thanks.

Eric Escamilla While I am running test query as per your code I get empty array[]. D i need to configure any thing else?

pratik gandhi You may want to add in System.out.println() or logger.info() messages in whichever class you are invoking...ContactAttributeMapperJSON. Also, be sure you are adding them to the json object (jo.put(id, attributes.get(id).get())) AND returning the object.